INSTALLATION INSTRUCTIONS
AMERICAN REVOLUTION DELUXE LED
American Electric Lighting a division of Acuity Lighting Group, Inc.
DRAWING NO. A72934 REV -- (FRONT)
©2014 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-72934
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
WARNING
!
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
FIGURE 1
CLOSED HOOD - STREET SIDE VIEW
CLOSED HOOD - STREET SIDE VIEW
FIGURE 2
OPEN HOOD - TOP VIEW
CUPOLA CAP
CUPOLA BASE
NEMA
LABEL HERE
-OPTIONAL-
LENS
PANELS (4)
TRIGGER
LATCH (2)
-OPTIONAL-
CUPOLA LENS
ADJUST PHOTO-
CONTROL BY LIFTING
& TURNING CUPOLA
SIMULTANEOUSLY
HOOD
CLOSURE
SCREW
BOSS
SCREW NOT
SHOWN
LOWER HOUSING
LENS
PANELS (4)
LOWER
HOUSING
SET SCREWS (3)
LADDER REST (2)
-OPTIONAL-
MIN POLE OD 2.375”
MAX POLE OD 3”
OPENING & CLOSING THE UNIT:
OPENING & CLOSING THE UNIT:
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
ABOVE).
2. REMOVE THE STREET SIDE LENS.
2. REMOVE THE STREET SIDE LENS.
3. LOCATE THE WIRING DIAGRAM ATTACHED INSIDE OF THE
3. LOCATE THE WIRING DIAGRAM ATTACHED INSIDE OF THE
HOOD. USE AS A GUIDE FOR CONNECT THE POWER
HOOD. USE AS A GUIDE FOR CONNECT THE POWER
SUPPLY LEADS TO THE TERMINAL BLOCK.
SUPPLY LEADS TO THE TERMINAL BLOCK.
4. PULL UP THE TERMINAL BLOCK COVER.
4. PULL UP THE TERMINAL BLOCK COVER.
5. UNSCREW THE TERMINAL BLOCK SCREWS AND CONNECT
5. UNSCREW THE TERMINAL BLOCK SCREWS AND CONNECT
PROPER THE SUPPLY LEADS ON EACH POSITION.
PROPER THE SUPPLY LEADS ON EACH POSITION.
6. TIGHTENING THE SCREWS FROM TERMINAL BLOCK.
6. TIGHTENING THE SCREWS FROM TERMINAL BLOCK.
RECOMMENDED TORQUE FOR SCREWS 35 IN-LBS.
RECOMMENDED TORQUE FOR SCREWS 35 IN-LBS.
7. PUSH DOWN THE TERMINAL BLOCK COVER.
7. PUSH DOWN THE TERMINAL BLOCK COVER.
8. REINSTALL THE STREET LENS.
8. REINSTALL THE STREET LENS.
9. CLOSE THE UNIT.
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF
AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF
THE REFLECTOR PLATE ASSEMBLY OR UL COVER.
THE REFLECTOR PLATE ASSEMBLY OR UL COVER.
WIRING:
TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE
THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
2. UNSCREW THE TWO
CAPTIVE
CLOSURE SCREWS. YOU WILL
KNOW
T
HE SCREWS ARE COMPLETELY DISENGAGED FROM
HE SCREWS ARE COMPLETELY DISENGAGED FROM
THE HOOD
WHEN
THE SCREWS CAN MOVE FREELY UP AND
THE SCREWS CAN MOVE FREELY UP AND
DOWN.
3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
TIGHTEN
THE TWO CA
TIVE CLOSURE SCREWS.
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
SIMPLY PULL
BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
INDEX FINGER WHILE
PUSHING UP ON THE HOOD WITH YOUR
PUSHING UP ON THE HOOD WITH YOUR
THUMBS. CLOSE THE UNIT BY
THUMBS. CLOSE THE UNIT BY
CLOSING THE HOOD AND PRESSING
CLOSING THE HOOD AND PRESSING
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
WARNING
FIXTURE MUST BE GROUNDED
TO FUNCTION AS INTENDED
!
(3 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals